Hauppauge Wintv Hvr 1600 Driver For Mac

Note: to use the WinTV-HVR-955Q with Windows Media Center, click the Windows Media Center install tab above.

New product installs:

Latest WinTV application and driver for Windows WinTV version 8.5 application and Windows drivers. Note: If you have run HCWCLEAR, you must reboot your PC and leave the WinTV-HVR-1950 installed.After a reboot you will see the Found New Hardware Wizard installation message, hit Cancel. Then continue below. Note: to use the WinTV-HVR-1950 with Microsoft's Windows Media Center application (DVB-T.

If you have recently purchased a new WinTV product and your WinTV v8.5 Activation Code has never been used, you can install WinTV v10 with this code. This only applies to unused WinTV v8.5 Activation Codes.

Installation notes for WinTV v8.5:

If you have one of the following products: a Hauppauge WinTV-HVR-850, WinTV-HVR-950, the original Colossus or HD PVR model 1212, you must use WinTV v8 or WinTV v10. WinTV v8.5 does not support these products.

A WinTV v8.5 Activation Code will be needed to install this WinTV v8.5 version. If you do not have an Activation Code, but you have a WinTV v7 CD, you can install the WinTV v8 application.

If you do not have an Activation Code: If you do not have a WinTV v8/8.5 Activation Code, you can purchase the new WinTV v10 Activation Code on the Hauppauge webstore for $12.95. This can be used with WinTV-HVR, WinTV-dual and WinTV-quad products, as well as the HD PVR series of HD recorders plus USB-Live2 and the ImpactVCBe.

Extend: If you have an Activation Code for WinTV v8 or v8.5 with Extend, the latest version of WinTV v8.5 with Extend will automatically be installed.

Installation on multiple computers: the WinTV application can be installed on as many PCs as needed as long as you use the same Hauppauge device. We link the serial number of your TV tuner (sometimes it's the MAC address) with the Activation code. So as long as you use the same Hauppauge device, you can install on more than one computer.

WinTV v8.5 application and Windows driver package

WinTV v8.5 is the latest version of the WinTV v8 application for Windows. This download is a complete WinTV v8.5 application, including Windows drivers for supported WinTV products plus utilities.

WinTV v8.5 Installer
For Windows 10, 8, and 7

Version: 37350 File size: 101 MB Date: Dec. 24, 2019
Release notes Backup download site Previous version

To install the WinTV v8.5 application

• Step 1: Download the WinTV v8.5 installer by clicking the download button above. The WinTV v8.5 Installer is normally saved in the Download folder on your PC
• Step 2: Run wintv85setup from the Download folder on your PC. Halfway through the installation, a message will pop up asking for you to enter the Activation Code.
• Step 3: At the Activation required screen, click on Enter Activation code and enter the activation code which was emailed to you, is printed on the WinTV v8 activation card or printed on your WinTV v8 CD. You do not need to enter the dashes, and you can use upper or lower case characters.
• Step 4: When the installation is complete, you will find the WinTV icon on your Windows desktop. Double click on this icon and the WinTV application will run. On the first run of WinTV, it will automatically go through the TV source selection and will scan for channels.

To install the latest driver:

Leave your WinTV-HVR plugged into your PC. Follow the following steps:

• Download the WinTV-HVR driver update
• Run HCWDRIVERINSTALL.EXE.
• This will install the WinTV-HVR base driver. At the completion of the driver install you should see a message which says Drivers have been updated successfully.

SoftMCE Setup

File name: SoftMCE_setup.exe
File size: 2.3 Mb
Date: 4/14/2010

Setting up your TV tuner in Windows 7 Media Center

Bug fixes for the Windows Media Center 'Low bit rate' error message

Microsoft has released Windows Media Center patches for the 'Low bit rate' error message.
Click to view the information from Microsoft.

Remapping clear QAM channels in Windows 7 Media Center

WinTV Digital Signal Strength Indicator

The WinTV Digital Signal Strength indicator displays information about the quality of the digital TV channel you are watching. This application is used with the WinTV v7 and WinTV v8 applications.

Click here for instructions on using this application.

IR Remote control application

Remote control applet. After you run this applet, an icon will appear in your Windows device tray showing that the Hauppauge remote control is active.

Name: 2.71.33113_IR32.exe
Size: 450KB
Updated: April /2015

WinTV-Scheduler update for WinTV version 6

This TV program scheduler for WinTV version 6 allows 'background recording' on dual tuner WinTV products.

Name: sched25_26071.exe
Size: 3.8 MB
Updated: March 11, 2008

None at this time.

NextPVR

NextPVR is a free Personal Video Recorder (PVR) and Media Centre application for Microsoft Windows. NextPVR works with most Hauppauge TV tuners.

JRiver Media Center

JRiver Media Center is a TV application for managing and playing digital media. JRiver Media Center can record and play Over-The-Air and Cable TV broadcast channels using TV tuners from Hauppauge. You can currently record on one machine and watch on another, or on a tablet. All the user has to do in install the drivers for their Hauppauge product and JRiver Media Center can do the rest. You can download a fully featured version of the product on a 30 day trial from www.JRiver.com to experience the magic of JRiver Media Center.

Linux for the WinTV-HVR-955Q

LinuxTV.org is distributing the open source driver for the WinTV-HVR-955Q. Please see here.

For the Hauppauge close source Linux driver, please send an e-mail message to: jfox@hauppauge.com

Linux for the WinTV-HVR-950Q

WinTV version 6 users manual

WinTV version 6 users manual
Updated: October 15, 2007

Making a TV connection to your WinTV

What Operating Systems are supported by the WinTV-HVR-955Q?

• Microsoft® Windows® 10, 8 and 7, Windows Vista, either 32-bit or 64-bit versions
• Windows XP, Windows XP Pro or Windows XP Media Center Edition, with Service Pack 2 ( or greater.)

Can I use the WinTV-HVR-955Q with Media Center?

Yes, the WinTV-HVR-955Q can be used with Windows Media Center in Windows 8, 7, Vista and with Windows XP Media Center Edition 2005.

To use the WinTV-HVR-955Q with Windows Media Center, download and install the Windows Media Center driver installation package, which will install the WinTV-HVR-955Q Windows driver and the Hauppauge MCE Soft Encoder.

Note: Under Windows 7, the Hauppauge MCE Soft Encoder is pre-installed as part of Windows 7. Therefore, you can skip the installation of the MCE Soft Encoder and simply install the WinTV-HVR-950Q Windows driver.

Note: under Windows Media Center, you will only be able to configure WinTV-HVR-955Q as either an Digital tuner or an Analog tuner. You will not be able to switch between Digital and Analog channels.

What type of channels will I receive with the WinTV-HVR-955Q?

NTSC Analog CableTV or over-the-air analog TV: You can use your cable TV from the wall to connect to the WinTV-HVR-950Q and receive all of your basic Cable TV channels. You can also use a roof top antenna to receive 'over-the-air' TV.

Note: After June 2009, most areas in the United States no longer broadcast over-the-air analog signals.

ATSC over-the-air digital TV: Supports all ATSC formats, up to the high definition 1080i format!
Note: For ATSC digital TV, a rooftop/out door antenna is recommended for optimal results/signal strength.

ClearQAM cable TV Channels: Clear QAM digital cable TV channels are unencrypted digital cable TV channels. Clear QAM allows users to watch unencrypted digital TV channels from their cable TV provider without a set-top box.
Note: WinTV v8, WinTV v7 or Microsoft Windows 7 is required for clear QAM reception
Note: Check your local cable TV provider for clear QAM reception over your cable TV network.

Can I get HD with the WinTV-HVR-955Q through my Cable or Satellite box?

What type of recordings can I make with the WinTV-HVR-955Q?

Using the WinTV 7 or WinTV v8 application, the WinTV-HVR-955Q will record in a transport stream (TS)
For ATSC and Clear QAM digital TV recordings, the recording format and bit rate is exactly the same as the broadcast format (i.e. ATSC 1080i is recorded at 1080i).
For NTSC analog cable TV recordings, our SoftPVR is used to create Transport Stream files (TS)

Note: TS files can be converted to MPEG files using options in the WinTV 7 configuration menu.

Note: The WinTV 6 application recording are in MPEG format for both digital and analog.

Note: Not all recordings made with ATSC/QAM signals are DVD compliant.

Can I record one show while watching another with the WinTV-HVR-955Q?

No. The WinTV-HVR-955Q will only be able to record the program that is being viewed using the WinTV v8 application. But the Hauppauge WinTV v8 application allows up to 4 WinTV-HVR-955Q's to be used in one system at a time.

Black video window or choppy video when watching a digital TV channel

If you are watching a digital TV channel and you see choppy video, no audio or a black screen, then it is possible your PC is not fast enough to decode and play the digital TV channel you are watching. Please verify that your system meets the minimum requirements for using the HVR-950Q

Digital TV, especially ATSC high definition digital TV, is very CPU intensive. Many graphics cards have special built-in hardware to speed up decoding of high definition TV channels.

On graphics cards without special video decoding features, you can often improve the playback performance by using the Video Renderer settings located in the settings menu of WinTV 7. To open the setting menu click on the “gear” button located in the lower left of the WinTV 7 screen.

The default mode is EVR. The other modes are VMR9, VMR7 and Overlay. Each mode uses a different process to render video. Try each mode and use the one which gives you the best results. To use hardware acceleration put a check in the box “use hardware acceleration when possible. This will allow your graphics system to use hardware acceleration for video decode. Note: graphics hardware acceleration does not work on all systems. After making a change in video rendering settings Wintv must be restarted to take effect.

If you are using WinTV 6 then the render options are part of a separate program called Primary. Changes in the Primary applet must be made with the WinTV application closed. Open the Primary program by going to Start – All Programs – Hauppauge WinTV – Primary. After making changes close the Primary applet and open the WinTV application.

How do I enable my remote control so it will work with the WinTV-HVR-950Q?

The IR software should be installed by default. To check look for a small remote control icon in the Windows task bar on the lower right. IF it is not present you can reinstall Wintv from the installation CDROM or download IR32.EXE from our support web site. The remote control must also have “line of sight” with the HVR-950Q. The IR receiver of the HVR-950Q is the round bulb on the side of the unit.

I receive a 'Low bit rate' error message when using Windows Media Center in Windows 7.

WinTV application locks or stops responding during analog scan under Windows 7.

In order to fix this issue, please check that your Power Options setting is not set to ‘Power Saver’. Please change it to ‘Balance’ or ‘High Performance’.

To change these settings on Windows 7, please do the following.

Click on Start and then Control Panel.

If Control Panel is set to View by: Category then click on ‘System and Security’ and then ‘Power Options’.

If Control Panel is set to View by: Large or Small icons then click on ‘Power Options’.

If you do not see Balanced or High Performance please click on the option for ‘Show additional plans’.

Once you make the change please restart your system. When the system restarts please rescan again for channels.

What file size will the recorded videos be?

Digital Broadcasts (ATSC or QAM)

The file size of a digital signal capture depends on the bitrate of the digital signal. The bitrate is set by the broadcaster and cannot be user configured. Bitrates for digital signals can range anywhere from about 1.2 Mbits/sec up to 19.3 Mbits/sec. Most of the time these bitrates are variable and not constant. Capture sizes for ATSC & QAM recordings are approximately 1.7 Gigabytes per hour up to 8.3 Gigabytes per hour.

Analog Broadcast.

The WinTV application has to convert analog signals to digital in order to record. There are four recording profiles. The following list shows recording file sizes for burning to 4.3Gb DVD:

Best - Approx 1 Hour+
Better - Approx 1 1/2 Hours
Good - Approx 2 Hours
Fair - Approx 3 Hours

WinTV v7 does not open or opens and then disappears?

This can be caused by a corrupt Channel database so you will need to uninstall and reinstall. First you need to go to start, all programs, Hauppauge Wintv and in that folder run
“uninstall Wintv7” (or remove Wintv7 using control panel 'add/remove programs) then you need to remove the backup channel database.

Windows Vista, 7 and 8 go to C:program data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search
Options) once you can get to this folder you will see a folder label “Hauppauge” delete this folder.

Windows XP go to C:documents and settingsall usersshared documentsapplication data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search Options) once you can get to this folder you will see a folder label “Hauppauge” delete this folder.

Then download the latest version of Wintv7 located in the support section of the website and reinstall (note: you must have your original CD to validate the download.)

Windows cannot verify the digital signature for the drivers required for this device error code 52?

This appears to be a bug in windows 64 bit OS. Our drivers are signed.

Baldur's gate enhanced edition gog keygen for mac. 'Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)'

The following is probably the easiest fix to Error Code 52 on Windows 7 or Windows 8 64bit.

In device manager right click the Hauppauge product under Sound Video and Game Controllers with the exclamation mark and select Uninstall. If you have a USB product you might multiple listings, please right click the first one on the list.

For this example we will use the HVR-950Q.

On the Confirm window please check the box for 'Delete the driver software for this device' and click OK.

Repeat the uninstall for the other two 950Q entries. (note you won't be asked to 'confirm device uninstall' again).

Once the drivers are gone on right click on 'Sound, Video Game Controllers' and 'Scan for Hardware Changes'.

Windows should now look online automatically for the 950Q drivers.

Take a look after a few minutes if the drivers are installed automatically properly under Sound Video and Game Controllers.

If they still come back as 'unsigned' try the procedure again.

Here is a chart which shows some of the things you need to know about each type of connection.

First time installation of WinTV v7 or during a reinstallation: “WinTV board not found” or “No TV tuner available”

Broadway while recording

Step 1: Check the status of your Hauppauge TV tuner drivers in Windows Device Manager

• Click Windows Start, click on Control Panel and click on Device Manager
• In Device Manager, click on Sound, video game Controllers
• You should see your Hauppauge product

Step 2: If the Hauppauge device has a yellow exclamation mark

Click on the Hauppauge device to open it. If you see the following: 'Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)'
This appears to be a bug in Windows 64 bit OS since the Hauppauge Windows drivers are signed.

The following is the easiest fix to Error Code 52 on Windows 7 or Windows 8 64bit.

• In Device Manager, right click the Hauppauge product under Sound Video and Game Controllers with the exclamation mark and select Uninstall. If you have a USB product you might see multiple listings, please right click the first one on the list. (For this example we will use the WinTV-HVR-950Q. )
• On the Confirm window please check the box for “Delete the driver software for this device” and click OK
• Repeat the uninstall for the other two WinTV-HVR-950Q entries (Note: you won’t be asked to ‘confirm device uninstall’ again)
• Once the drivers are removed, right click on Sound, Video, Game controllers and click Scan for Hardware Changes
• Windows should now look online automatically for the 950Q drivers
• Take a look after a few minutes if the drivers are installed automatically properly under Sound Video and Game Controllers.
• If they still come back as “unsigned” try the procedure again

Errors when running WinTV 7: “TVserver cannot Start” or “.NET framework' errors

This can be caused by a corrupt WinTV v7 Channel Database. You will need to uninstall and reinstall the WinTV v7 application and the Channel database to fix this.

To uninstall WinTV v7, click Windows Start, click on All Programs, click on Hauppauge WinTV run Uninstall Wintv7. You can also or remove Wintv7 using control panel 'add/remove programs'.

Then you need to remove the backup Channel database:

• Windows Vista, 7 and 8: Go to C:program data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search Options) once you can get to this folder you will see a folder label “Hauppauge”. Delete this folder.
• Windows XP: Go to C:documents and settingsall usersshared documentsapplication data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search Options) once you can get to this folder you will see a folder label “Hauppauge” delete this folder. Then download the latest version of Wintv7 located in the support section of the website and reinstall (note: you must have your original CD to validate the download.)

Settings.xml file is corrupt or missing

Solution: Uninstall WinTV v7 and then reinstall WinTV 7

• Click Windows Start ->Control Panel and then click Programs and Features
• Find Hauppauge WinTV 7 and double click on this. This will start the uninstall process
• When you are finished uninstalling WinTV v7, reinstall it from your WinTV v7 CD

Prodinfo: get information on your Hauppauge TV tuner

Prodinfo.exe is a program you can run which will extract information about the WinTV product you have installed such as model and serial number, MAC address, revision, and features which can be used to identify the exact model of your product. The driver for the device must be installed in order to run Prodinfo.exe

HCWClear: remove the Hauppauge driver and applications from your PC

HCWCLEAR.exe is a program you run to remove all driver and files that were installed with the installation of the WinTV program.

WinTV Windows driver and WinTV v7 latest version download WinTV v7 application and driver download packageFor Windows 8, 7, Vista and XPFile name: wintv7cd3.9g.exeFile size: 151.4 MBDate: This download is a complete installation package, including drivers for supported WinTV products plus the WinTV v7 application and utilities. Installation notes:A valid WinTV application CD-ROM will be needed to install this WinTV v7 version. Any WinTV v6 or WinTV 7 application CD can be used during the install.If you have a WinTV v7.2 CD-ROM with Extend, then the latest version of WinTV Extend will also be installed.

To install the WinTV v7 application update. Download the WinTV v7 installation package to your PC. After downloading this file, the file is normally saved in the Download directory on your PC. Run wintv7cd.exe from the Download directory on your PC. Click Step 1. Install Drivers.

This will install the WinTV Windows driver. At the completion of the driver install, you should see a message which says Drivers have been updated sucessfully. Click Step 2. Install WinTV. This will install the WinTV v7 application, 'middleware', TV services and other necessary files.This will complete the driver and application installation for your WinTV.

Release notes for WinTV v7:. Adds support for HD PVR 2 models 1573xx. Fixes an issue installing IR on drives with 2TB+. Fixes an issue which could cause scheduled recordings not to start after a reboot if the database had got too large. Updated translations.

Adds support for HVR-1955/HVR-1975. Windows driverFile name: HVR-9x051032528153SIGNED.zipVersion: 5.10.325.28153Size: 1.37 MBTo install the latest Windows driver only:Leave your WinTV-HVR-900 plugged into your PC. Follow the following steps:. Download the WinTV-HVR-900 driver update.

Unzip this file to a directory you will remember, such as WINTV. Yakuza encounters. It will create a new folder. To install, open the folder.

Run HCWDRIVERINSTALL.EXE. This will install the WinTV-HVR base driver. At the completion of the driver install you should see a message which says Drivers have been updated successfully.